Table of Content
Wrap the Press Cable over a 4 1/2” Pulley in the direction shown. Wrap the Ab Cable around a 3 1/2” Pulley in the direction shown. Slide the Pulley and a Cable Trap onto the 3/8” x 3 1/2” Carriage Bolt already inserted into the Butterfly Base . Before beginning, make sure that you have read and understood the information on page 4.
Place the bracket on the lower end of the Press Upright over the indicated 5/16” x 2 1/2” Carriage Bolts in the Press Base . Do not overtighten the Nylon Jamnut; it must be easy to pivot the Leg Lever. Place the bracket on the lower end of the Butterfly Upright over the indicated 5/16” x 2 1/2” Carriage Bolts in the Butterfly Base .
Weider Pro 9940 Weight machine - $285 (Fairport)
Locate the parts for the seat assembly. Bolt the backrest to the butterfly upright and bolt the seat to the seat plate. Bolt this plate to the butterfly seat frame. Attach the seat on the press seat frame in the same way.
Bolt this to a hole a few inches from the base of the press upright. Attach a pulley on the inside of the press frame and wrap the cable through. Take it through another pulley and attach it to the leg press lever. Lead it back to the upright and up to the top of the upright.
Weider pro 9940 - $100 (Ephrata)
Locate a V-pulley and wrap the butterfly cable around it. Bolt the V-pulley and a large cable trap to the bracket at the back of the butterfly upright. Wrap the butterfly cable around a 3 1/2-inch pulley and then attach it to the small pulley bracket on the back of the butterfly upright. Wrap the cable around another V-pulley and bolt the V-pulley and a large cable trap to the bracket at the back of the butterfly upright. Bolt the end of the butterfly cable to the bracket on the right butterfly arm.
Attach the loop at the end of the cable to the hole at the bottom of the small leg lever and secure it with a bolt, washers and jamnut. Locate the parts for the arm assembly. Push plastic bushings onto the welded tube of the press frame. Attach the press frame to the press base with a lubricated bolt and locknut that allow it to pivot. Push caps onto the press arms and bolt one into each side of the bracket on the press frame.
Weider Pro 9940 Home Gym - $200 (West Lafayette)
Attach the bench press upright to the press base and bolt the support frame to both the press base and the upright but do not tighten the locknuts yet. Push a square inner cap into the end of the press top frame then bolt it onto the top of the bench press upright. Push a square inner cap into the end of the press seat frame and then bolt it to the press base and press upright but do not tighten it yet. Attach the leg press lever to the press base with a lubricated bolt and locknut. Use carriage bolts to attach the press base to the weight base with nylon locknuts, but do not tighten them yet.
Insert four 5/16” x 2 1/2” Carriage Bolts up through the indicated holes in the Press Base . Insert a 3/8” x 2 1/2” Carriage Bolt and a 3/8 x 4” Carriage Bolt up through the indicated holes at the end of the Press Base . Insert four 5/16” x 2 1/2” Carriage Bolts up through the indicated holes in the Butterfly Base .
Attach the Butterfly Cable to the bracket on the Left Butterfly Arm with a 3/8” x 1” Bolt and two 3/8” Nylon Jamnuts . Press a Weight Tube Bumper into the lower end of the Long Weight Tube . Slide the Weight Tube into the center holes in the Weights . Press a Weight Tube Bumper into the lower end of the Short Weight Tube . Before you begin the assembly process itself, take the time to complete the steps outlined here. Read all precautions and instructions in this manual before using this equipment.
Wrap it round another pulley and bolt that pulley and a cable trap onto the bracket on the butterfly base. Take the threaded end of the ab cable under the pulley mounted in the weight base and then wrap it around a 4 1/2-inch pulley. Attach this to the bracket on the weight top frame. Attach the threaded cable end to a U bracket with a washer and nut.
Save this manual for future reference. To use the Curl Pad , remove the 2” Square Inner Cap from the Front Leg and insert the Curl Post into the Front Leg. Secure the Curl Pad by inserting the Adjustment Knob at the desired height.
Attach the bumper to the front of the front leg with a tap screw. Attach the small leg lever to the bracket on the front leg with a lubricated bolt and nylon jamnut that allows it to pivot freely. Locate the parts for the cable assembly. Bolt the 52-inch butterfly cable to the bracket on the left butterfly arm.
Push caps into both ends of the two butterfly arms and wet the lower ends of the arms with soapy water. Lubricate the axle on the butterfly top frame and attach the butterfly arms using retaining rings and outer caps. Gently tap with the mallet to secure.
The resistance needs to be adjusted over a period of time, to ensure that you reach your training goals. This can be done by changing the weights or the workout routine. Workouts for the Weider Pro 9940 weight bench and home gym system are varied and will thoroughly test your mettle. Insert a 1/4” x 2 1/2” Carriage Bolt through the center hole in a Seat Plate .
No comments:
Post a Comment